Fr tho I needed this vid
Linux wont take off until the friction for new users is low enough that the layman can resolve issues without resorting to techniques outside of their understanding and patience. Even as someone who uses linux, there are a ton of things that should have a GUI / just be a context menu entry. If you can get the same amount of work done with a button click rather than typing out a complicated command line string, you might as well use the GUI, right click menu, etc. and make it easier for the typical person. People these days can barely use tablets, and those already dumb things down to icons you tap. Unfortunately, making it accessible to the lowest common denominator is what makes things popular a major factor in making things popular
Also if you want a domain but dont care about the actual address, a .xyz domain composed entirely of numbers with less than 10 digits is $1-2 + same as renewal fee per year. $1.22 for me on porkbun
Just be sure to redact the whois information bc you will get a call from scammers trying to get you to register your domain on some “internet map” for a small fee acting as if its some step in your setup process you havent done yet
Choosing rice either wasn’t random or you just stumbled onto “ricing” and “ricers” which comes from a derogatory name for Japanese motorcycle and cars in the 60s-80s? (“rice burner” and “rice rocket”). . Ricing/ricer later became a term for modded cars/motorcycles which were popular in Japan.
That’s where r/ricing and “Linux ricing” came from for Linux/unix theming. It’s not unique to that either. People use the term for their gaming rigs. An example of “ricing” in this context is adding tons of RGB LEDs. Some people consider the term racist, other people don’t care and continue to use it
The ones for autism :•|
I felt the same the first time I tried but it honestly takes a few tries to start getting it right. The kind of iron and solder matter a lot; the older ceramic core ones suck and the JBC/pinecil type are much superior. Part of the problem with the ceramic type ones is they have one setting - full blast - and not good temperature control. With a pinecil/JBC you can set the temperature to 300C and expect to get 300C. Too hot and it will boil off the flux before you’re done soldering and you just get crud.
In terms of solder, leaded rosin core solder is the best. Don’t worry about the lead, as long as you wash your hands. Use a brass sponge type thing to clean the tip frequently to remove crud
For through holes, I’d say get some veroboard off eBay and a bunch of cheap resistors and just start plugging away until you get better. Process is basically - have tip with a bit of solder, poke to pad and pin, put solder into joint and hold 1-3 seconds until solder flows onto pad and pin, remove tip. Putting some flux on in advance helps remove the oxides before soldering
For surface mount (side pads/pins), there are kits with cheap/obsolete/trash components you can just plug away at without fear of messing anything up. Soldering smt is a bit annoying but doable by hand without much training. the process is basically: tin one pad, use tweezers to place part and reheat the solder until the part is in place, solder the rest of the pads, reheat first pad to relieve stress.
Even for large parts, I used to have trouble with unsteady hands. If you are doing smt you really need a microscope or magnifying glass for anything smaller than 0805 - really helps with the visual feedback loop for hand positioning. A microscope significantly improved my dexterity and hand steadiness
Perhaps a low table or an office chair without arm rests to get a closer to waist level
There’s a name for that; nominative determinism
Mud
To fix tunnelled candles, maybe try wrapping them in foil to help heat the outer edges and level them out
I thought theory was a fire/smoke leaking /explosion inside the tent caused by the homemade stove leading to them cutting their way out and running, and then getting separated and lost in the confusion, before succumbing to hypothermia
Oh man the FreeCAD discussion
I also use fusion and while FreeCAD has improved significantly, it’s still lacking in critical areas
The replies are always “but it’s gotten better”
Yeah, and it still pops up and error and wrests control away if you dare select a dimension tool and points/lines in the “wrong” order
To the tune of The Twelve Days of Christmas