This is indeed sad news. I’ll forever be grateful to him. He made the door that got me through into Proxmox. God rest his soul.

You are a man of culture. Great choice.

I did too, but never cared again after my wife finally switched over to Fedora. I have nobody else that I care about enough using windows.

Yeah, when forced to use Windows it’s way worse because we know the other end of the spectrum.

I know, the irony.

You have the option to get a solid hardware that you can install openwrt on, and then use the Deco mesh just for the Wifi. That’ll give you similar, if not the same results, and save you a few bucks in the process.

I just started migrating my network from PFSense, a bunch of tplink switches and Aruba InstantOn APs to unifi. I’m almost done (just missing a couple of APs more and 1 more switch), and I honestly am extremely happy with the decision. The Unifi APs are not as powerful as the Arubas, but the improvements to the performance of my network more than makes up for that.

I apologize. I misunderstood that you were looking for a mesh system that would work with an existing openwrt router. Seems what you’re looking for is a mesh system that can be flashed with openwrt.

For that I can only suggest that you look at the supported hardware table and see if you can find what you need.

https://openwrt.org/toh/start

Editing my previous comment for my mistake.

If you’re not looking to segregate your network or any other “advanced” network feature, you can’t really get better value that Tplink Deco.

Edit: I misunderstood what the op was asking for. This answer is not valid for that.

Lol

⏫ That!

I self host Freshrss and have a PWA for it. I also have Feeder in my Obtainium just in case, but it’s not currently installed.

Never used ansible before. All I know is that it seems to work with Ubiquiti edge switches.

https://docs.ansible.com/ansible/latest/collections/community/network/edgeswitch_vlan_module.html

I’ve only had it for about 4 months, but no annoyances so far. It did crash once, and it takes (in my opinion) ridiculous amounts of time to fail over a Vlan when one of my Lans goes down (upwards of 5 minutes, when my PFSense was almost instant), but other than that, it’s been super solid.

With the current browsers panorama, it’s important to use more than 1 browser. My main browser is Librewolf, then Brave for work, and Mullvad for all the rest. The reason being that almost every site is made to work first on Chrome and everything else is an afterthought (so I use Brave for those).

I’m in the (long) process of migrating a mix of PFsense + Tplink switches + Aruba Instant On APs to a fully unifi infrastructure. Even with the mix of devices, my network has been way more solid than ever with a Unifi Gateway Ultra, a few NanoHD APs (still mixed with some Arubas) and 1 unifi switch assisted by the rest of the tplinks.

I should finish the migration next week, no regrets.

The level and ease of control I have now would not have been possible with the previous infrastructure.

If you can still return the Omada devices, I suggest you do and go Unifi.

It is GUI (for the most part, you can also modify the yml file).

https://github.com/ilya-zlobintsev/LACT

This is cool. If you’re worried about the safety on their instance, spin your own. They have a very clear and simple docker way to do just that.

Sounds exactly like my setup for the last 5 years, minus NGINX (don’t need it with Cloidflared since each service is it’s own Proxmos Container and use their own exclusive tunnels).

It’s a great looking site at first glance (haven’t signed up yet). I just sandboxed a browser and let it run without forcing HTTPS. Funny thing is that it does show it as being https when disabling https enforcement.

I’ll take it for a spin this afternoon when I get back home (or in my phone when I get bores at the recital my wife is forcing me to go to 🤣🤣🤣).